Services / Price List
Action Work
ALL action work is indicated true within .0001” or less tir concentricity from the center line of the actions bolt bore using GTR Tooling and dual Mitutoyo .0001” indicators. A full action blueprint can ONLY be done if a new barrel blank will be installed. The action threads are single point re-bored and re-cut from .005” - .040” oversize for a full clean up and a MCR 1/4" dual draft recoil lug is included on all non integrated actions.
Remington Action Blueprint
$300
Models 600, 7, 700, 721, 722, XP-100 and 40X.
Single point re-cut action face and internal locking lugs perpendicular to the bolt bore center line.
Single point re-cut action threads concentric with the bolt bore center line.
Single point re-cut rear of bolt lugs and bolt face perpendicular to the bolt body center line.
MCR .250" Dual Draft Recoil Lug bored and fitted.
Howa & Weatherby Vanguard Action Blueprint
$300
Single point re-cut action face and internal locking lugs perpendicular to the bolt bore center line.
Single point re-cut action threads concentric with the bolt bore center line. ( Metric Threads ) Single point re-cut rear of bolt lugs and bolt face perpendicular to the bolt body center line.
Winchester
$250
Single point re-cut action face and internal locking lugs perpendicular to the bolt bore center line.
Single point re-cut action threads concentric with the bolt bore center line.
Single point re-cut rear of bolt lugs and bolt face perpendicular to the bolt body center line.
Savage w/ Barrel Nut
$275
Single point re-cut action face and internal locking lugs perpendicular to the bolt bore center line.
Single point re-cut rear of bolt lugs and bolt face perpendicular to the bolt body center line.
Single point re-cut rear of barrel nut perpendicular to the barrel nut thread center line.
MCR .250" Dual Draft Recoil Lug bored and fitted .
*Receiver and barrel nut threads are NOT re-cut.*
Savage w/o Barrel Nut
$300
Single point re-cut action face and internal locking lugs perpendicular to the bolt bore center line.
Single point re-cut action threads concentric with the bolt bore center line.
Single point re-cut rear of bolt lugs and bolt face perpendicular to the bolt body center line. MCR .250" Dual Draft Recoil Lug bored and fitted.
* Barrel nut is eliminated, and action is locked up to barrels shoulder. *
Remington 8-40 Action Scope Base Holes
$125
Scope base holes are circular interpolated and thread milled. The new scope base holes will run parallel with the action center line.
* Opening up clearance holes in scope base or picatinny rail and 8-40 torx screws are extra. *
Remington Sako Extractor Conversion
$175
Models 600, 7, 700, 721, 722, XP-100 and 40X
With a sako extractor conversion you can change bolt face dia. from factory size to .223, .308, mag or ultra mag.
Fixes broken factory extractor and extraction problems.
Gives a more positive extraction with less effort.
Sako extractor kit Included
https://www.youtube.com/watch?v=Ti9-jFyLG6s
Dual Ejectors
$75
If you are using a low mounted scope with target turrets and you have a sako extractor conversion done, you may find that your brass is contacting your scope turret and dropping cases back into the loading port. Dual ejectors can correct that issue by changing the ejection angle closer to the 3 o'clock position.
Ejector kit included
Remington Bolt Knob Threading
$75
Models 7, 700, 721, 722
Bolt is held in MCR fixture and factory knob is turned and threaded 5/16-24
Spiral Bolt Fluting
$125
Add a custom look to your bolt with some spiral fluting
Remington Side Bolt Release
$175
Available for Right Handed Only
Bolt release kit included
Bolt Handle Skeletonized
$100
Add a custom look to your bolt with skeletonizing your handle
Barrel Work
All barrel work is bore indicated true within .0002” or less of concentricity using live pilot indicating rods and Mitutoyo .0001” dual indicators. in MCR’s barrel fixture. All chambers are cut using live pilot reamers held in a floating reamer holder.
Chamber Job
$385
Single point turn and thread to a class 3A fit
Chamber to minimum head space
Single point crown
320 grit finish
Custom engrave cartridge designation
Radial Muzzle Brake Install
$175
Vais Style
Muzzle Brake NOT included
Timed Muzzle Brake Install
$200
MCR 3 port style
Muzzle Brake NOT included
Thread Muzzle for Suppressor
$150
1/2-28 x .600"
5/8-24 x .600"
other threading sizes upon request
Barrel Fluting
$ 225
Straight
Spiral
Interrupted
Stock Work
Pillar Bedding
$300
NO plastic stocks. Wood, laminate, fiberglass and carbon fiber stocks only.
Pillars are manufactured in house using 9/16" dia. 6061 aluminum pillars.
Devcon steel is used for bedding compound.
Barrel channel may be opened up to ensure barrel is 100% free floated.
Action and recoil lug are bedded stress free.
Aluminum bedding block stocks are prepped so the bedding block acts as aluminum pillars around the front and rear guard screws.
Flush Cup Install
$37.50
NO plastic stocks. Wood, laminate, fiberglass and carbon fiber stocks only.
GrovTec heavy duty push button flush cups w/ 1" sling loops.
Price is for each flush cup w/ 1" sling loop and installation.
Swivel Stud Install
$15
NO plastic stocks. Wood, laminate, fiberglass and carbon fiber stocks only.
GrovTec 10-32 swivel stud and T-Nut.
Price is for each swivel stud and install.
Recoil Pad Installation
$100
NO plastic stocks. Wood, laminate, fiberglass and carbon fiber stocks only.
Fit and grind Pachmayr pads only.
Recoil pad NOT included.
Finishing
Bead Blast
Stock Finishing
Bead Blast
Barrel or barreled action - $50
Cerakote
Stock Finishing
Bead Blast
Action, bolt, barrel & bottom metal - $250
Scope Rail - $50
Scope Rings - $50
Bolt Flutes 1 color, bolt body 320 grit - $75
Bolt Flutes 2 tone - $150
Barrel Flutes 1 color, barrel 320 grit - $125
Barrel Flutes 1 color, barreled action 1 contrasting color - $300
Stock Finishing
Stock Finishing
Stock Finishing
Single color - $175
Single color w/ 1 color speckles - $200
Sponge camo w/ clear coat - $250
Hydro dip w/ clear coat - P.O.R
Custom painting - P.O.R